Important Plumber Tips for Installing a Bathtub
Important Plumber Tips for Installing a Bathtub
Blog Article
Right here down the page you might get a bunch of reliable points about How to Install a Bathtub Yourself.
Mounting a tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably difficult project. If the old tub is easily accessible, the task can relocate quickly; if you need to open up a wall to eliminate the old tub and place the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make sure you have actually certified yourself for the task and fit trying it. Rather than hiring a specialist to take over a halfway-completed project, it is far better to consider using one before you begin. Chances are you may require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your bathroom if you have actually currently purchased a brand-new tub and also do not require to change the setup of your previous water supply pipes.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Protect the faucet in place with the producer provided backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind needs to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wooden boards under its feet, position the bath tub in the needed setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bath tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system as well as examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bathtub and also check the overflow electrical outlet and the regular outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub ought to wait till the tub has been used at least once as this will resolve it right into its last placement.
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, creating the water to permeate the wall between the bathroom and also the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can break relatively early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the market. It is advisable to fit the tiles utilizing waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that entry on How to Install a Bathtub Yourself when doing a search on the search engines. For those who enjoyed our post plz be sure to pass it around. Thanks a bunch for your time. Kindly stop by our site back soon.
Don't delay; get expert help. Report this page